BILKA ALU 90 Foil

bilka alu90 1

BILKA ALU 90 Foil

Vapor barrier foil

BILKA ALU 90 Foil is a multilayer film consisting of one layer of metalized polypropylene film, polypropylene mesh, and polyethylene film. The BILKA ALU 90 Foil is designed to perform a vapor barrier in the construction of roofs. The metalized layer reflects thermal radiation, preventing heat loss. Product is an insulating barrier to water vapor and the wind. Such membranes can be used in all ventilated and non-ventilated roofs.

Technical characteristics:

  • specific weight: 90g/m²± 10%;
  • resistance to tearing: ≥100N
  • temperature range: -30 : 70⁰C
  • Sd 50m ± 30%
Product NameBILKA ALU 90 Foil
Package sizeRolls 1,5 m x 50 ml = 75 m²/roll
Purpose and usageDesigned to perform vapor barrier in the construction of roofs. The metallised layer reflects thermal radiation, preventing heat loss. Product is insulating barrier to water vapor and the wind.
Material: Multilayer film consisting of one layer of metallized polypropylene film, polypropylene mesh and polyethylene film.
CaracteristicsTest methodDeclared value
Roll lengthEN 1848-250m (-0/+2%)
WidthEN 1848-2 1,5m ± 0,5%
ThicknessEN 1849-20,20 mm (-0,01;+0,01)
Mass per unitEN 1849-290 g/m² ± 10%
Reaction to fireEN ISO 11925-2
E Class
Watertightness (2 kPa)EN 1928
Pass
Watertightness after artificial ageingEN 1296; EN 1928
Pass
Resistance to tearing (Longitudinal/Transverse)EN 12310-1≥100N / ≥100N
Maximum tensile stress (Longitudinal/Transverse)EN 12311-2≥220N/50mm / ≥150N/50mm
Elongation at break (Longitudinal/Transverse)EN 12311-2≥12% / ≥7%
Water vapour resistance
EN 1931
2,5*10¹¹ ± 30% m²Pa/hg
Water vapour transmission properties (Sd)EN 1931 50m ± 30%
Temperature range ---------- -30°C : 70°C
Chemical durabilityEN 1847 Pass
Joint strength EN 12317-2 NPD
Resistance to impact
EN 12691
NPD mm
Dangerous substances
-
NPD

Assemblage rules:

BILKA ALU 90 Foil should be mounted on the “hot” side of the thermal isolation of the roof or walls, aluminum side in the direction of the room. The foil can be laid in parallel or perpendicular to the roof rafters. In the case of perpendicular installation to the rafters, the installation should start along the roof’s crest and the following foil bands to be mounted under the previous layer, using a 15 cm overlap and seal the connection with the special tape. In the case of parallel installation to the rafters, mount continuously under the rooftop, using a 20 cm overlap and if possible, connect the foil strips in the rafters area and also seal with special tape. The foil should be fixed with nails or staples every 10-15 cm. After assembly, secure all fixing points, connection and foil joints with a special tape in order to prevent the infiltration of water vapor from the room into the thermal isolation layer.

Storage and warehousing rules:

Protected from direct exposure to atmospheric conditions, away from heat sources (min 1 m).

Warranty:

In compliance with the regulations in force, under the observance of the transportation conditions indicated by the supplier.

Related prescriptions, specifications:

EN 13984:2013

Possible risks, prevention prescriptions:

There is no risk of endangering health.

Ask for an offer

Please fill out the form and we will contact you for an offer in the shortest time.